Veröffentlichungen: 2010

Jahr: 2010

H. POTENTE; E. MORITZER; T. PLUGGE; M. SCHAEFERS; H.-P. HEIM; H. RIDDER: Advanced investigations for the newly developed special injection molding process: "GITBlow". 68th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Orlando (USA), 2010

H. POTENTE; V. SCHÖPPNER; H. HÖRMANN; M. BORNEMANN: Analytical modelling of the pressure/throughput and drive power behaviour in the melting section of single screw extruders considering wall slippage and shear thinning. Regional Meeting of the Polymer Processing Society, Instanbul (Türkei), 2010, S. 10-27

H. POTENTE; V. SCHÖPPNER; R. HOFFSCHLAG: Development of an Adaptive Process Optimization of Hot-Tool Welding Using an Innovative Actuation Concept. 68th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Orlando (USA), 2010

V. SCHÖPPNER; H. HÖRMANN; C. LAKEMEYER; K. ANGER; E. GIESE: Dynamic Temperature Measurement. In: Kunststoffe international, Heft 9, 2010, S. 117- 120

V. SCHÖPPNER; D. BONEFELD: Dynamische Druckfuehrung beim Laserschweissen von Kunststoffbauteilen. In: Ingenieurspiegel, Heft 3, 2010, S. 42-43

V. SCHÖPPNER; T. HALLMANN: Experimental Study of the influence of preshearing on the yield stress of carbon filled rubber. 26th International Conference of the Polymer Processing Society (PPS), Banff (Kanada), 2010

V. SCHÖPPNER; A. BAGSIK; E. KLEMP: FDM Part Quality Manufactured with Ultem*9085. 14th International Scientific Conference on Polymeric Materials, Halle (Saale), 2010

E. MORITZER; E. MÜLLER; C. FUNKE: Filling behaviour of wood-plastic composites (WPC) in the injection moulding process. 8th Global WPC and Natural Fibre Composites Congress and Exhibition, Stuttgart-Fellbach, 2010

C. FUNKE; M. SCHULTE: Injection-Moulded WPC-Products with genuine wooden surface - two steps in one. 8th Global WPC and Natural Fibre Composites Congress and Exhibition, Stuttgart-Fellbach, 2010

H. POTENTE; V. SCHÖPPNER; R. HOFFSCHLAG: Investigations into the melt adhesion during heated tool welding. In: Joining Plastics, 2010, S. 102 - 107

E. MORITZER; T. PLUGGE; M. SCHAEFERS: Kurz vor der Serienreife - Weiterentwicklung des innovativen Spritzgiesssonderverfahrens: GITBlow. In: Ingenieurspiegel, Heft 3, 2010, S. 44

H. POTENTE; V. SCHÖPPNER; P. KLOKE; J. RUDLOFF; M. BASTIAN; K. KRETSCHMER: Modelling the fibre-degradation during compounding of short fibre reinforced composites based on glass fibres and polypropylene. 26th International Conference of the Polymer Processing Society (PPS), Banff (Kanada), 2010

R. WEDDIGE; J. PAPE: Neue Schneckenkonzepte zur Leistungssteigerung. VDI-Tagung: Extrusionstechnik, Bonn, 2010

V. SCHÖPPNER; D. BONEFELD: Optische Eigenspannungsanalyse lasergeschweisster Kunststoffbauteile. In: Joining Plastics, Heft 1, 2010, S. 40-47

V. SCHÖPPNER; N. BÖHM: Quality comparison of WPC produced in an internal mixer and on a co-rotating twin-screw extruder. 8th Global WPC and Natural Fibre Composites Congress and Exhibition, Stuttgart-Fellbach, 2010, ISBN: 978-83-7518-226-2.

H. POTENTE; V. SCHÖPPNER; D. BONEFELD; R. MAHNKEN; A. SHABAN: Residual Stresses in the Quasi-Simultaneous Laser Transmission Welding of Amorphous Thermoplastics. In: Polymer Engineering and Science, 50. Jg., 2010, S. 1520-1526

V. SCHÖPPNER; P. KLOKE: SIGMA - Simulation gleichlaeufiger Doppelschneckenmaschinen. VDI-Tagung: Der gleichlaeufige Doppelschneckenextruder, Leverkusen, 2010

V. SCHÖPPNER; N. KRETZSCHMAR: Simulating Tightly Intermeshing Co-Rotating Twin Screw Extruders with SIGMA. Summer Computer Simulation Conference, Ottawa (Kanada), 2010

V. SCHÖPPNER; D. BONEFELD: Stressed by lasers. In: SPE Plastics Research Online, 2010

E. MORITZER: Structual glueing of plastic part. 2nd WJS/DVS Conference on Joining Plastics, Düsseldorf, 2010

V. SCHÖPPNER; H. HÖRMANN; C. LAKEMEYER; K. ANGER; E. GIESE: Temperatur dynamisch messen. In: Kunststoffe, Heft 9, 2010, S. 161-165

V. SCHÖPPNER; H. HÖRMANN; C. LAKEMEYER; S. KLUS; K. ANGER: Temperature modeling of the melt for tempered screws in single screw extrusion by giving constant heat fluxes. Regional Meeting of the Polymer Processing Society, Instanbul (Türkei), 2010, S. 10-34

E. MORITZER; C. LEISTER; R. WEDDIGE: Temperature-dependent lap shear strength of adhesively bonded high-temperature resistant thermoplastics. 63th Annual Assembly of the International Institute of Welding (IIW), Istanbul (Türkei), 2010

H. POTENTE; V. SCHÖPPNER; R. HOFFSCHLAG: Untersuchungen zum Schmelzeanhaften beim Heizelementschweissen. In: Joining Plastics, 2010, S. 102 - 107

E. MORITZER; E. MÜLLER; C. FUNKE: WPC fuellt anders. In: Kunststoffe, 2010