Veröffentlichungen: 1996 - 2000

Jahr: 2000

H. POTENTE; J. FLECKE; K. KRETSCHMER: A physico-mathematical model for the dispersion process in a co-rotating intermeshing twin screw extruder. 58th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Orlando (USA), 2000, S. 14 - 18

H. POTENTE; F. BECKER: A step towards understanding the heating phase of laser transmission welding. 53th Annual Assembly of the International Institute of Welding (IIW), Florenz (Italien), 2000

H. POTENTE; M. BASTIAN: Calculating Morphology Development of Polymer Blends in Extruders on the Basis of Results of Boundary and Finite Element Simulations Using the Sigma Simulation Software. In: Polymer Engineering and Science, 40. Jg., 2000, S. 727 - 737

H. POTENTE; K. LINNENBROCK; J. SCHNIEDERS; F. FERBER; K. P. HERRMANN: Determination of self-stresses in hot plate welded specimen by use of photoelasticity and the hole drilling method. 17th DANUBIA-ADRIA SYMPOSIUM on experimental methods in solid mechanics, Prag (Tschechische Republik), 2000, S. 187 - 190

H. POTENTE; M. BASTIAN; A. GEHRING; M. STEPHAN; P. P: Experimental Investigation of the Morphology Development of Polyblends in Corotating Twin-Screw Extruders. In: Journal of Applied Polymer Science, 76. Jg., 2000, S. 708 - 721

H. POTENTE; J. SCHNIEDERS: Influence of process parameters on the phenomenon of stress cracking during hot plate welding. 58th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Orlando (USA), 2000, S. 1122 - 1125

H. POTENTE; J. SCHNIEDERS; K. P. HERRMANN; F. FERBER; K. LINNENBROCK: Investigations concerning the development of inherent stresses during welding by using the drilled-hole method as well as the finite element method. 53th Annual Assembly of the International Institute of Welding (IIW), Florenz (Italien), 2000

H. POTENTE; H.-P. HEIM; TH. THUEMEN: Mathematical Optimization of Annular Non-Return Valves. In: Kunststoffe international, 2000, S. 52 - 54

J. JUNGEMANN: Plasticizing Extruder Model - Linking the Pressure and Throughput Models. In: Journal of Plastics Technology, 20. Jg., 2000, S. 225 - 236

H. POTENTE; J. JUNGEMANN: Pressure/Throughput Behaviour in the Melting Section. In: Journal of Polymer Engineering, 20. Jg., 2000, S. 329 - 350

H. POTENTE; H.-P. HEIM; TH. THUEMEN: Ring-Rueckstroemsperren rechnerisch optimieren. In: Kunststoffe, Heft 8, 2000, S. 92 - 94

H. POTENTE; B. KRELL; S. KRAMME: Scale-up rules for blow heads. 58th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Orlando (USA), 2000, S. 868 - 872

H. POTENTE; W. TOEBBEN: Simulation of shearing and mixing sections. 58th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Orlando (USA), 2000, S. 99 - 105

H. POTENTE; K. LINNENBROCK; J. SCHNIEDERS; F. FERBER; K. P. HERRMANN: Spannungsrissbildung an amorphen Thermoplasten infolge des Heizelementschweissprozesses. In: DVM-Berichte Festigkeits- und Bruchverhalten von F, Heft 232, 2000, S. 239 - 248, ISSN: 0943-3473.

H. POTENTE; M. BASTIAN; T. A. OSSWALD; ST. KRAWINKEL: Stroemungssimulation mit BEMflow. In: Plastics-Special, 2000, S. 30 - 34

H. POTENTE; F. RECKERT: The processing of renewable rescources using a short single screw extruder with a combined section for solid conveying and plastification. 58th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Orlando (USA), 2000, S. 292 - 296

Jahr: 1999

H. POTENTE; M. BASTIAN; J. FLECKE: Design of a Compounding Extruder by Means of the SIGMA-Simulation Software. In: Advances in Polymer Technology, 18. Jg., 1999, S. 147 - 170

H. POTENTE; B. KRELL; F. RECKERT: Hot Plate Welding of Blow Molded Parts: Influence of the Blow Molding Process on Weld Strength. 57th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), New York (USA), 1999, S. 1025 - 1028

H. POTENTE; CH. OBERMANN; J. PAPE: Influence of Model Simplifications on the Accuracy in Single Screw Extrusion. 15th International Conference of the Polymer Processing Society (PPS), Hertogenbosch (Niederlande), 1999

H. POTENTE; J. SCHNIEDERS: Influence of the hot plate welding process on the stress cracking of PMMA and PC. 52th Annual Assembly of the International Institute of Welding (IIW), Lissabon (Portugal), 1999

H. POTENTE; J. KORTE; F. BECKER: Laser Transmission Welding of Thermoplastics: Analysis of the Heating Phase. In: Journal of Reinforced Plastics and Composites, 18. Jg. Heft 10, 1999, S. 914 - 920

H. POTENTE; M. BASTIAN; P. POETSCHKE; M. STEPHAN: Morphology Development of Polymer Blends in Twin Screw Extruders.15th International Conference of the Polymer Processing Society (PPS), Hertogenbosch (Niederlande), 1999

H. POTENTE; H.-P. HEIM: Moulded Part Design for the Gas Injection Technique. 57th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), New York (USA), 1999, S. 556 - 560

E. MORITZER: Processoptimisation with new sensor technology. In: Society of Plastics Engineers, 1999

H. POTENTE: Simulation des Prozessverhaltens von Schneckenmaschinen. In: Kunststoffe, 89. Jg., 1999, S. 83 - 94

V. SCHÖPPNER: Stretching Thermoplastics: Current Plant Developments and Theoretical Description. 15th International Conference of the Polymer Processing Society (PPS), Hertogenbosch (Niederlande), 1999

H. POTENTE; F. BECKER: Weld Strength Behavior of Laser Butt Welds. 57th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), New York (USA), 1999, S. 1402 - 1405

Jahr: 1998

E. MORITZER; M. NEUMANN: Adaptive Spritzgiessprozessoptimierung. NOVAtech Automotive Engineering International, 1998

H. POTENTE; J. FLECKE: Analysis and Modeling of the Residence Time Distribution in Intermeshing Co-rotating Twin Screw Extruders Based on Finite Element Simulations. In: Journal of Reinforced Plastics and Composites, 17. Jg., 1998, S. 1047 - 1054

E. MORITZER: Das Fliessbild muss stimmen! Konstruktionsrichtlinie zur verfahrenstechnischen Auslegung von GID-Artikeln und deren Werkzeuge. In: Plastverarbeiter, 1998

H. POTENTE: Fundamental Mechanismus in Polymer processing - Extrusion -. 56th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Atlanta (USA), 1998, S. 3604 - 3614

J. SCHNIEDERS: Grundlagen und aktuelle Forschungsaktivitaeten zum Thema Kunststoffschweissen. Haus der Technik: Kunststoffteile richtig schwei, Essen, 1998, S. 1 - 12

H. POTENTE; A. BRUE; D. KOENIGHAUS: Heizelemente mit Profil. In: Plastverarbeiter, 49. Jg. Heft 2, 1998, S. 80 - 84

H. POTENTE; A. BR: Heizelementschweissen von gefuellten und verstaerkten Thermoplasten. In: Schwei, 50. Jg. Heft 3, 1998, S. 172 - 179

H. POTENTE; J. KORTE; F. BECKER: Laser Transmission Welding of Thermoplastics: Analysis of the Heating Phase. 56th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Atlanta (USA), 1998, S. 1022 - 1025

H. POTENTE; J. KORTE; F. BECKER: Laser transmission welding of thermoplastics: Analysis of the heating phase. 51th Annual Assembly of the International Institute of Welding (IIW), Hamburg, 1998

H. POTENTE; J. FLECKE; J. VOGEL; B. KRELL: Mit SIGMA dichtkaemmende Gleichdrall-Doppelschnecken-Extruder optimieren (Teil 3a). In: Plastics-Special, 1998, S. 24 - 26

H. POTENTE; V. SCHÖPPNER; ET AL.: Optimierung mit Hilfe statistischer Modelle. In: Kunststoffberater, Heft 3, 1998, S. 27-35

H. POTENTE; M. ZELLEROEHR; M. STRUNZ: Prozessverstaendnis durch multiple Simulation von Einschneckenextrudern. In: Kunststoffberater, Heft 6, 1998, S. 26 - 30

H. POTENTE; TH. HUCHTEMEIER; M. BRINKSCHROEDER; H.-P. HEIM: Prozesswissen aufbauen und nutzen (Teil II). In: QZ, 43. Jg., 1998, S. 66 - 70

H. POTENTE; A. BRUE: Welding behavior of Filled and Reinforced Thermoplastics with Hot Plate Welding. 56th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Atlanta (USA), 1998, S. 1062 - 1066

H. POTENTE; A. BRUE: Welding behaviour of filled and reinforced thermoplastics with hot plate welding. 51th Annual Assembly of the International Institute of Welding (IIW), Hamburg, 1998

E. MORITZER: Werkzeuginnendruckmessung außerhalb der Kavitaet. In: Kunststoffberater, 1998

Jahr: 1997

H. POTENTE; J. FLECKE: Auslegung eines Compoundierextruders mit Hilfe der Simulationssoftware SIGMA. VDI-Tagung: Optimierung des Compoundierprozesses durch Rezeptur- und Verfahrensverstaendnis, Baden-Baden, VDI-Verlag, 1997, S. 39 - 87

H. POTENTE; J. JUNGEMANN: Establishment of the shear stresses acting on the solid bed surrounded by flowing melt. 55th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Toronto (Kanada), 1997, S. 239 - 263

H. POTENTE; A. BRUE: Investigations into increasing weld strength through the use of profiled hot plates. 55th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Toronto (Kanada), 1997, S. 1233 - 1237

H. POTENTE; A. BRUE: Investigations into increasing weld strength through the use of profiled hot plates. 50th Annual Assembly of the International Institute of Welding (IIW), San Francisco (USA), 1997

H. POTENTE; J. KORTE: Laser Butt Welding: Analysis of the Heating Phase. 50th Annual Assembly of the International Institute of Welding (IIW), San Francisco (USA), 1997

H. POTENTE; J. KORTE; R. STUTZ: Laser-Durchstrahlschweissen von PE-HD. In: Kunststoffe, 87. Jg., 1997, S. 348 - 350

H. POTENTE; J. KORTE; R. STUTZ: Laser-Durchstrahlschweissen von PE-HD. In: Kunststoffe Plast Europe, 87. Jg., 1997, S. 27 - 29

H. POTENTE; J. KORTE: Laserstumpfschweissen. In: Kunststoffe, 87. Jg., 1997, S. 590 - 594

H. POTENTE; J. FLECKE: Materialverhalten von Zweistoffsystemen. In: Kunststoffberater, Heft 5, 1997, S. 10 - 22

H. POTENTE; J. JUNGEMANN; M. ZELLEROEHR: Mathematisch-physikalische Modelle - Statistische Methoden - Teil 1. In: Plastics-Special, Heft 9, 1997, S. 24 - 26

H. POTENTE; J. JUNGEMANN; M. ZELLEROEHR: Mathematisch-physikalische Modelle - Schnecken-Optimierung - Teil 2. In: Plastics-Special, Heft 10, 1997, S. 16 - 19

H. POTENTE; TH. HUCHTEMEIER; M. BRINKSCHROEDER; H.-P. HEIM: Mit Continuous Process Control zu mehr Qualitaet (Teil I).In: Kunststoffberater, Heft 1/2, 1997, S. 16 - 20

H. POTENTE; J. GEILEN; B. KRELL: Mit neuer Strategie zu effektiver Qualitaetssicherung. In: Kunststoffberater, Heft 4, 1997, S. 32 - 37

H. POTENTE; J. JUNGEMANN; TH. WENNIGES: Physico-mathematical and Process-concurent Statistical Simulation of Extrusion Processes. In: Polimeri, 18. Jg., 1997, S. 36 - 49

H. POTENTE; M. BASTIAN: Prediction of Morphology - Development of Immiscible Polyblends in Co-Rotating Twin Screw Extruders with SIGMA. Polyblends, Montreal (Kanada), 1997, S. 397 - 408

H. POTENTE; TH. WENNIGES; C. WEHMEYER: Prozessoptimierung bei Mehrfachwerkzeugen. In: Kunststoffe, 87. Jg., 1997, S. 972 - 974

H. POTENTE; M. BRINKSCHROEDER; H.-P. HEIM; TH. HUCHTEMEIER: Prozesswissen aufbauen und nutzen. In: QZ, 42. Jg., 1997, S. 1381 - 1387

H. POTENTE; A. UJMA; H. STOCKBRUEGGER: Regelung der Formteilmasse von spritzgegossenen Formteilen. In: Kunststoffberater, 1997, S. 20 - 28

H. POTENTE; E. MORITZER: Schaumstrukturen schwaechen das GIT-Bauteil. In: Kunststoffberater, 1997

H. POTENTE; B. KRELL: Screw optimisation by means of DOE and multiple regression. 55th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Toronto (Kanada), 1997, S. 135 - 139

H. POTENTE; J. FLECKE; M. BASTIAN: SIGMA - Computer-Aided Process Simulation of Tightly- Intermesing, Co-Rotating Twin-Screw Extruders. Materiales Polim, Centre Catal, 1997, S. 11 - 30

H. POTENTE; J. FLECKE; M. BASTIAN: SIGMA - Rechnergestuetzte Prozesssimulation dichtkaemmender Gleichdrall-Doppelschneckenextruder. VDI-Tagung: Der Doppelschneckenextruder - Grundlagen und Anwendungsgebiete, Baden-Baden, VDI-Verlag, Duesseldorf, 1997, S. 435 ff.

V. SCHÖPPNER; J. JUNGEMANN: Simulationsmodelle für Einschneckenextruder - Grundlagen, Grenzen und Moeglichkeiten. VDI-Tagung: Der Einschneckenextruder: Grundlagen und Systemoptimierung, Baden-Baden, VDI-Verlag, Düsseldorf, 1997, S. 353-386

H. POTENTE; V. SCHÖPPNER; A. UJMA: Successful simulation of wall-slipping plastics. In: Journal of Polymer Engineering, 17. Jg., 1997, S. 153 - 170

H. POTENTE; J. FLECKE: The Breaking Down and Agglomerating of Fillers in Polymer Melt: A Physical Model for Mathematical Description. In: Journal of Reinforced Plastics and Composites, 16. Jg., 1997, S. 1281 - 1292

H. POTENTE; A. UJMA: The influence of raw material batch fluctuations on the injection moulding process and product quality. 55th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Toronto (Kanada), 1997, S. 462 - 466

F. BECKER; A. BR; TH. HUCHTEMEIER; J. KORTE: Trends bei Serienschweissverfahren. In: Kunststoffe, 87. Jg., 1997, S. 1632 - 1640

H. POTENTE; A. LIMPER; J. FLECKE; H. STIEGLITZ: Zwei sinnvolle Werkzeuge, RELMA und SIGMA zur Auslegung von Direktextrusionsanlagen - Teil 1 -. In: Kunststoffberater, Heft 10, 1997, S. 29 - 35

H. POTENTE; A. LIMPER; J. FLECKE; H. STIEGLITZ: Zwei sinnvolle Werkzeuge, RELMA und SIGMA zur Auslegung von Direktextrusionsanlagen - Teil 2 -. In: Kunststoffberater, 1997, S. 61 - 67

Jahr: 1996

H. POTENTE; U. MELISCH; K. P. PALLUCH: A Physico-Mathematical Model for Solids Conveying in Co-Rotating Twin Screw Extruders.In: International Polymer Processing, Band XI, Ausgabe 1, 1996, S. 29 - 41

H. POTENTE; E. MORITZER: Alles fließt nach unten. In: Plastverarbeiter, 47. Jg., 1996, S. 56 - 57

H. POTENTE; E. MORITZER: Alles fließt nach unten: GID-Formteiloptimierung. In: Plastverarbeiter, 47. Jg., 1996

H. POTENTE; B. KRELL: Continuos process control for improved quality assurance in extrusion blow molding. 54th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Indianapolis (USA), 1996, S. 991 - 995

H. POTENTE; E. MORITZER; CH. OBERMANN: Foam formation in GAIM-Parts: Theoretical and Experimental Considerations. In: Polymer Engineering and Science, 36. Jg. Heft 16, 1996

H. POTENTE; E. MORITZER; CH. OBERMANN: Foam Formation in Gas-Assisted Injection Molded - Parts: Theoretical and Experimental Considerations. In: Polymer Engineering and Science, 36. Jg., 1996, S. 2163 - 2172

H. POTENTE; J. LIU; A. RUECKER: Gelatinierungsverhalten von Weizenstaerke in einem zweiwelligen Knetgeraet. In: Starch - Staerke, 48. Jg., 1996, S. 171 - 174

H. POTENTE; E. MORITZER: GID-Formteile optimiert gestalten. In: Kunststoffberater, Heft 3, 1996, S. 22 - 25

H. POTENTE; E. MORITZER: GID-Formteile optimiert gestalten. In: Kunststoffberater, 1996

H. POTENTE; J. KORTE: Laser Butt Welding of semi-crystalline Thermoplastics. 49th Annual Assembly of the International Institute of Welding (IIW), Budapest (Ungarn), 1996

H. POTENTE; J. KORTE: Laser butt welding of semi-crystalline thermoplastics. 54th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Indianapolis (USA), 1996, S. 1255 - 1259

H. POTENTE; N. EFFEN; A. UJMA: Mehr Transparenz durch Simulation. In: Kunststoffberater, Heft 10, 1996, S. 12 - 17

H. POTENTE; U. MELISCH; J. FLECKE: Mit SIGMA dichtkaemmende Gleichdrall-Doppelschnecken- Extruder optimieren - Teil 2 -. In: P1: Spezial-Fachzeitschrift für den Thermoplast- und Elastomerverarbeiter, 1996, S. 5 - 9

H. POTENTE; U. MELISCH; J. FLECKE: SIGMA - Computer aided process simulation of intermeshing co-rotating twin-screw extruders.54th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Indianapolis (USA), 1996, S. 334 - 337

H. POTENTE; A. UJMA: Simulation of the plasticating phase of injection moulding machines. 54th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Indianapolis (USA), 1996, S. 802 - 806

H. POTENTE; A. BR: Spannungsrissbildung an heizelementgeschweissten Heckleuchten. In: Kunststoffberater, Heft 5, 1996, S. 18 - 21

H. POTENTE; J. FLECKE: The Division of Polymers in Molten Environment of Polymers: A Physical Model for Mathematical Description.54th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Indianapolis (USA), 1996, S. 178 - 183

H. POTENTE; A. BRUE: The problem of stress cracking in heated tool butt welded tail lights made of PMMA and ABS. 54th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Indianapolis (USA), 1996, S. 1292 - 1296

H. POTENTE: The problem of stress cracking in heated tool butt welded tail lights made of PMMA and ABS. 49th Annual Assembly of the International Institute of Welding (IIW), Budapest (Ungarn), 1996

H. POTENTE; U. MELISCH: Theoretical and Experimental Investigations of the Melting of Pellets in Co-Rotating Twin-Screw Extruders.In: International Polymer Processing, Band XI, Ausgabe 2, 1996, S. 101 - 108

H. POTENTE; E. MORITZER: Theoretical And Practical Results For The GAIM-Process Variant: Melt Displacement Into An Overflow Cavity. In: Society of Plastics Engineers, 1996

H. POTENTE; E. MORITZER: Theoretical and practical results for the gas injection molding process - Variant: Melt displacement into an overflow cavity. 54th Annual Technical Conference of the Society of Plastics Engineers (ANTEC), Indianapolis (USA), 1996, S. 674 - 678

H. POTENTE; N. EFFEN; J. LIU: Throughput calculation with considerations of leakage flow on injection molding plasticizing units. In: Polymer Engineering and Science, 36. Jg., 1996, S. 1557 - 1564